Recent content by PJS010LGC

I finally found the issue with my door side slide not easily retracting. Since we have gotten the unit a couple of years ago, this slide has required the herky jerk (rapid in and out movement of the switch until the slide finally started moving inward). I managed to get it retracted eventually...

Re: 2010 Landmark - 12V fuse for AC keeps blowing Dan, I just remembered that, coincidentally with the first fuse failure, Sharron also reported that the under counter lighting, which is rope LED lighting had quit working. So I went back out to the RV to see if the switch was still on and it...

Re: 2010 Landmark - 12V fuse for AC keeps blowing Dan, I separated the 2 wires. I checked both leads for a dead short and only one lead was shorted, the other was open. I reconnected the wire that I left the spade terminal on, installed my last 15 amp fuse, checked the 12V leads at the AC...

Re: 2010 Landmark - 12V fuse for AC keeps blowing Thanks Dan, Yes, you read that right. I was hoping that there might be a wiring diagram around that might show the device connected to the second white/orange. I looked but can't find. So you're right, it will be process of elimination. I was...

Re: 2010 Landmark - 12V fuse for AC keeps blowing Dan, Do you mean, the air return of the AC unit. I have the connector, on the side of the control box, disconnected, the white with orange stripe wire disconnected from the 12v+ lead into the control box. The tiny wires to the thermostat are...

The 12v fuse for the AC in my 2010 Landmark recently blew while RV'ing. A replacement fuse fixed the problem. Yesterday while parked at home, the fuse blew again but replacement fuses blew upon insertion. I opened up the AC unit ,disconnected the 12V wring and hooked the VOM to the disconnected...

Yesterday, I was cleaning out the front compartment and actually got inside the compartment. While there I noticed that the large wires to the relay adjacent to the motor, were loose, especially the center feed wire. I tightened the fasteners and, thinking I had fixed my slide problem, went...

Bob and Patty, The battery was fully charged when re-installed but I haven't checked it since. I have to try a bunch of things as suggested here but they are mostly electrical in nature and I keep wondering if there is a mechanical issue that is making it tough to retract the door slide...

We pulled our RV out of storage this last weekend. I had ordered a ball seal kit and a floor seal kit. I pulled the commode out yesterday and took it outside to completely clean it. The ball seal groove had lots of gunk in it, the ball seal was feeling a little brittle and the ball had gunk on...

We pulled our RV out of storage on the weekend. When we tried to extend either of the 2 lower slides they just grunted but after I pushed the retract side of the switch they moved in just slightly and then extended no problems. The off-door slide just rolls across the floor until fully...

Dometic shipped out of Canada so we got the pieces back at the beginning of March. We retrieved the RV out of storage over the weekend and I changed out the guides the other day. There is a huge difference in the contour of the tracks and this new contour ensures that the flap will be closed...

Thanks for all the suggestions. I have a list of things to look at when we get the rig out of storage at the end of the month Regards, John

This might be the problem with our commode as well. We seen some seepage out from under the base at floor level. I was wondering if it was the seal between the commode and black tank inlet but this could be it. Have not noticed anything running down the outside of the toilet. Is this an internal...

Dan, How quick do these mini breakers reset, because I don't recall a dead spot while I was playing with the slide. Where are these mini breakers located? As well, I need to find out what is binding or making it tougher to begin moving in. For the off door slide I can see the front rollers...

Dan, The part that's confusing me is that the the slide eventually moves in. I hear the grunting as an attempt is made to retract but, unless the breaker is auto resetting, I don't think its the circuit breaker getting tripped. I haven't had a chance to lubricate anything yet so that will be on...