Re: It’s been a great ride!
I believe we will all be back up and running in a month or so, maybe sooner. So, I got to believe HL is treating the current economic state as being in somewhat of a strategic pause.
Most of you reading this post are probably going to laugh at me here, but i've got a recent story to share on my experience with the emergency breakaway switch - here it goes - as I was leaving Mayport Naval Station (Pelican Roost - waterfront site) this weekend. While moving forward and exiting...
Re: washer/dryer fit for front bedroom install Cyclone
Jerapais - based off past experience collaborating with Pinnacle on repairs and warranty, i would not recommend anything pinnacle. On your other questions, I'm sure other's on the forum are better postured to offer you advice.
Good luck.
I just shut-off the main breaker prior to disconnecting from shore power, and then after connecting to shore power turn on the main breaker. Are there other circuit breakers that [should] be turned off prior to disconnecting from shore power?
Before I upgraded, I heard the IS upgrade would raise the rear height of my Landmark. However, my IS installation did not raise my Landmark's height. I was 13.3 going in, and 13.3 coming out. Hope this helps.
I re-read my post this AM and noticed I made an error. I am re-posting part of my message to correct my error: replace 2.0X2.5 gear roller package with 2.5X2.5 gear roller package. My bad.
I just replaced the rear kitchen slide gear roller a couple weeks ago because the gear and slide arm was not aligned. I purchased the entire 2.0X2.5 15 gear roller package from the Lippert website. (The right slide gear roller on mine is a 2.0X2.0) To remove and install the gear roller package...
ummmm...I have not seen this before. My initial thought is something with the bearings, but its just initial thinking. I agree you should send your pictures to MoRryde and ask for feedback.
I need to replace the right rear gear pack (right slide, looking from the front) P/N: 122837 (Ref: Lippert spec sheet on Dan's post below). I am wondering if anyone who has experience repairing/replacing the gear pack can tell me if the gear pack is a 15 gear tooth or an 18 gear tooth. I am...
Guess I am in the minority on this thread. My OEM NEXENs lasted 50k (mostly towing miles). I replaced them with Michelins LTX MS2 Defender. No issues with the Michelins after 20k. I have GY G114s on my Landmark.
We like our 2016 Newport 365. Replacing the spring axles with 8k MorRyde IS and 8kPSI disc brakes and electric heat were the two best two modifications. I also installed two U hangers in the front wardbrobe section to strengthen the clothes rod. Good luck.
Looks nice. I like how you laid it out as-well-as the hoses. Only recommendation I can provide is to use the 5micron flter as your first filter followed by the .5micron filter. Again, nice workmanship.
My bride and I have been FT in our 2016 Newport Landmark 365 for a couple years now. Only issues we have had is the D-Seals (crap), gear rollers on the two main slides, and my main awning motor needed to be replaced. I upgraded to MorRyde IS and pin box after purchase and installed GY G114 H tires.
When entering JAX, FL (from North) I would take I-295 W (Orange Park) versus I-295E (Daytonna Beach) or I-95 through JAX. Both I-295E and I-95 (in JAX) are under construction. (Recommendation).
Thanks John. I checked the 20A fuse (good) and the switch (good). No sound from the motor. Is this the correct troubleshooting procedures to determine if the awning motor is faulty? Thanks, Mike
Just arrived at Pecan Park RV Resort in Jacksonville, FL from VA. After getting settled-in yesterday, i depressed the exterior (front) awning and it would not extend. It worked fine prior to departing VA. The slide awning extends and retracts ok. I checked for obstructions on the front awning...
I remember seeing a Jayco Pinnacle in Crossville, TN last month who attached his ladder under the front of his 5th wheel trailer. I thought it was a good idea. I carry my ladder in the back of my truck. I'd be interested on how your ladder looks under your trailer (if you go ahead and do it)...
Thanks Jim. Can you share the size & dimensions of the plastic tubing you used?
I checked all the connections to the fresh water tank, and all looks well. I dryed up the insulation and put it back together this morning. I look forward to hearing back on the plastic tubing. Hopefully it will...
Thanks for the information Dan. I checked around the yeti pad. I cannot see any leakage around that area. The other possibility is the input water line connection to the tank. i need to cut under the rear IS axle to see that area. Thanks again.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.