Search results

Yep! I relabled it and checked the rest. All good now. I appreciate everyone's help!

Me too. I figured it was something simple. At least I know all the components of the slide system are good

Yep. That is for the actual Bed lifting mechanism.

Ok, we have victory! So it turns out that a 15 amp fuse named (Ceiling Lights) was burnt and was directly tied to the Rocker Panel switches for the Electric slides only...my hydraulic slides worked fine. Had to use a 20 amp until I can get some more 15 amp fuses. Funny thing is, this fuse has...

Ok, I have an update. I was able to run a isolated (direct) 12v source to one of the motors and still no response. (Testing done with and without shore power) I am showing 14.75/12.8 volts at the controller J7/J8 power input side. I am also showing the same voltage on the switch side (J8 +...

It looks like this may be what I have to do since I am getting power at all 3 controllers. Haven't tested power out to motors yet. Will have to check that tomorrow. It's just so odd that all 3 controllers are having the same issue.

I am getting power at all 3 controllers, not sure if this is possible or not with a short. As soon as I plug power back in, it goes back to the 9 blinks. I find it extremely odd that all 3 would be experiencing the same issue. I may have to chase the brown wires down 1 by one.

Yep, sure do. 13.4 to 13.8 on both ends.

Yes, just checked the 80 amp buss, 13.8 in and out. Same for the one up top.

Yes, definitely odd. This leads me to believe that there is a some component that has the ability to shut down all 3 slides. I replaced the batteries because they didn't hold a load, but that still didn't do a thing.

The Batteries were definitely weak as they did not hold a load. I bought some new ones and still nothing. Manual bypass does nothing either. What could cause all 3 slides to be dead? There has to be some kind of master control or fuse that operates all 3. The only thing I did recently was...

I am preparing for a move and noticed that all 3 Schwintek Slides are giving a Error Code #9 for a "Hall pwr short to GND". I hear zero activity when I press the switches to pull the slides in. I tried the manual override, lights started flashing, but no action. I have checked the 2 breakers...

Re: No power to Control panel Got it! Turned out it was a fuse on the Relay Board. Thanks again for all the help! Sent from my SM-G965U using Tapatalk

Re: No power to Control panel I do not. I opened the KIB panel looking for something with fuses and saw nothing. Also, I am not a 100% sure what I am looking for. Do you have a picture? Sent from my SM-G965U using Tapatalk

Re: No power to Control panel Yes, all those are working which is why I am stumped. I read 14.8V to 14.9V coming in to LCI panel. I have power coming into to the light switch panel (KIB) Awhich is why I suspected some kind of relay/remote connected to the blue wire? Sent from my SM-G965U using...

Re: No power to Control panel The LCD Display that shows my voltage and videos for my rig is the one that is dead. I have checked all the fuses/ breakers up front and all is in order. I updated my post with a couple of pictures and info. Sent from my SM-G965U using Tapatalk

Re: No power to Control panel Hi, None of the switches work to the lights. The board does not light up either. There is also a small lcd screen that shows the tank levels, that does not power up either. I saw the blue remote wire and wondered if there was a relay that regulated it. I...

Need a little guidance here. Both my LCD and control panel for lights have no power. Currently, I can not turn the interior lights on or off. I have 14.9 volts coming in to the LCD panel but it does not power up. The wires that feed the control panel for the lights have power but I have...

That is good to know, thanks! Sent from my SM-G965U using Tapatalk

Good to know. Thanks for the info! Sent from my SM-G965U using Tapatalk

We were actually considering the GE Profile series. We may end up going that route. Sent from my SM-G965U using Tapatalk

Our Furrion OTR Microwave convection oven is a gonner. Does anyone have any recommendations for a quality replacement? Sent from my SM-G965U using Tapatalk

After every ones input, I decided it was best to just hook up to the truck. I do however, plan on getting some sort of cribbing system for future work. You folks are awesome, I appreciate it! Sent from my SM-G965U using Tapatalk

Can two 6000 pound jack stands be used to support the front end while the landing gear is temporarily pulled in for a hydraulic fluid swap? Im sure it would be best to hook up to the truck, but just curious if this alternative would work. I have a Phoenix. Thanks

It will have it if it has the Arctic (Yeti) package. The holding tank heater pad switches should be next to all your other switches. Sent from my SM-G965U using Tapatalk

That was going to be my next approach. Thanks! Sent from my SM-G965U using Tapatalk

Has anyone had any issues getting a hold of Heartland? Specifically for warranty issues? I have sent multiple emails and left multiple voicemails with my direct contact and have not heard a peep in over a month. I am still trying to fix warranty issues that I filed over a year ago. I'm...

I have the 2018 Phoneix and it is just bare bones on the Lippert system, no wifi, no blue tooth either. Sent from my SM-G965U using Tapatalk

Carl, I emptied the fridge and gave it a good wipe down. At first it didnt seem to help but these last couple of days it seems that the smell is finally dissipating. My guess is that whatever had caused the smell had soaked into the vent system and took a while to wear out. Cleaning the...

It is only noticeable when opening the door. Smells like rotten potatoes or vegetables. I checked underneath the fridge after removing the kick panel. It looked clear. Not sure what the deal is. I may have to completely disassemble the interior and clean it. Maybe that will work better than...

Yes, we have an Arm n Hammer box in there now and unfortunately didnt put a dent in the smell. Sent from my SM-G965U using Tapatalk

No, it slowly developed over a few days and never went away. Sent from my SM-G965U using Tapatalk

Has anyone experience an odor that would not go away? We have emptied out or Insignia residential fridge and still can not track down nor get rid of the smell. Any ideas ? Sent from my SM-G965U using Tapatalk

I may end up doing that vs relying on the locals. Sent from my SM-G965U using Tapatalk

We have a Furion convection microwave in our 2018 and it works great but we prefer to bake in our Furion gas oven. Sent from my SM-G965U using Tapatalk

Hey all, I spoke with Heartland and they agreed to send me a replacement. I am very thankful for that. I live in a town where the local talent is not very motivated. That being said, I have found it a bit challenging to enlist help. The nearest RV dealer was no better. I left it with...

That's what I suspected. I already have the s/n and the phone number. I will more than likely install it my self. The place I live in has a shortage of independent mobile repair people "willing" to do anything. I am a Engineer by trade, any chance I could bill for my time? Just curious. Sent...

I was thinking something similar as well. Yes it is still under warranty but I currently have over 20 other items that have been pending repair for almost a year (11 months). Sent from my SM-G965U using Tapatalk

Thank you for the response. Yes, shut the power down. I actually removed the reel and inspected everything and snugged it all up. The arcing sound is not coming from anything visible, it literally sounds like it is inside, behind the red termination panel where the power chord connects to the...

Yes sir, I checked those as well. Sent from my SM-G965U using Tapatalk