Search results

Have these like brand new. Have the brackets to go into the elevator 400$ Located in north west Arkansas , Springdale area

Have a like new deck kit. Has the gate at the rear not the side. No steps. Has all the hardware 500$ in northwest Arkansas have the mounting brackets for cyclone and another can’t remember what they came off.

Mine is brass I tightened the fitting I haven’t see it leak again but I slept all night lol. I’ll be checking it next week

I came back today and water was dripping so I started looking as it was a pretty good drip. It was the hot water line on the back of the hot water heater. It must’ve been very slow and just kept going down the line. The lines for the slideout go out in that area. I have had a fan going for 3...

Water lines for the sink don’t even go into the floor. They are in the slide out. No clue where water would get in there

I will check this evening. It’s strange that it’s in that spot. Even if I drop coraplast there’s another black cloth holding in the insulation. What a pain. I move to this spot about a month ago. Was at last one a year and half never a issue. Maybe soemthong came loose when moving

Ok so I’m baffled here. I have a cyclone 2014 4000. And right in front of the couch I noticed a soft spot a week ago. I thought huh must’ve always been there , tonight I noticed it got bigger. So I took the cups out the hold the table, and the insulation is moist , stinks like mold. There is to...

I did the air flow mod, and right after that I started having issues. The air flow was great but the unit started freezing up. It freezes on the inside of the coil not the intake side with the sensor in it. I pulled off the cover after a night of ac running and the ice was a inch thick on the...

Well the chute is back togther. Wasn’t as bad as you’d think. I have it now so if something happens again I can take it apart easy.

Well it’s out but I got to fix the pipe now. It made it all the way to the tank. It’s probably 3.5 feet of pipe to make it that far and 2 45S silly. I will use 2 fermco to put it back together

I’m wondering if I can snake a wet dry vac Line down the hole and get it to suck it up

No fermco(rubber boot) they are all glued on. I just can’t beleive the thing went past the 45at the top. It may have 5-7 gallons of water in it. I could cut it use fermco to put back togther. I hate to take off commode as to don’t have any issue but I bet I will once I take it off.

Luckily I cleaned out the tank last night so it’s only got one bomb in it now lol it’s a plastic wand so no magnet. How deep are the tanks?

Well this morning water was froze when I went to flush. I pushed paper down so flap would close and on the pull out the brush caught the side and slipped out of my hand and down the poop shooot. I wouldn’t think it would get past both the bend but as I looked down I don’t see it in the first...

Those are the ones kind of. Mine needs a 90 fitting on one end. The ends are big you can turn with the hand. A true faucet line has a small 3/8 end that tightens to the stop valve with a wrench. The plastic end is 1/2 inch

I have those off and can see some of the tank not sure where the vent will be. I will crawl in there and look better.

It’s like this but has a 90 on one end and is 20 inches long https://www.rockrnd.com/item.asp?subclass=Faucet%20Installation&category=Supply%20Lines&subcat=Braided%20Poly%20fa&mpartno=14180 - - - Updated - - - The inside diameter at theblowes stores are different. They have a smaller hose...

My lines are leaking on the flexible line connected to the pump they say 1/2 faucet line. But both ends are big. Not like a faucet line at Lowe’s. One end is big and one small there. Where do I get a big double end? Can I get the washers inside the fitting at Lowe’s? They leak in the center...

I wonder how I can get to it to see.

Well still a smell down there not as bad. Can’t figure it out. Wonder if a mouse died or something

I’ve noticed as it gets full it makes it smell in the basement. And in time if it’s not emptied inside will smell also. The tank had no water in it or deodorizer so I’m wonder if that’s it. I’m gonna open it up today see if the smells gone

I emptied the black tank today. And usually I fill it up some but I was doing this before work and didn’t have time to fill it up 25%. I went to work and left the tank heaters on went in the basement about 14gours later man it stunk. No way that little tank heater melted a hole did it? It was...

That’s what my plan was. But I think I have a 1k deductible. Can’t remeber I think one of the arms got bent also

We had a big storm come in at night. Usually don’t get wind but this time we did. It ended up tearing the top of my awning about 3 inches. My guess is it will keep ripping. How hard is it to replace the awning fabric? I have a cyclone 4000 year 2014

I have a red flame now but it just shuts itself off. Guessing a short inside. Is there a better replacement ? Or do they all suck? I’d kind of like one that has a small vent off it where you can run heat to another room. Say like a furnace has vents to the room.

Well this problem has came back for me. I was able to shut off breaker and turn back on reset it. Worked fine all winter last year and been fine this fall but tonight it popped. I reset breaker and turn heat on it starts to blow heat a second later the thing pops internally and the numbers...

Thank you. I will be getting a set soon.

I have a cyclone 4000 2014year. I want to out the morryde steps but the threshold seems to be a different style then the pics they show. Mine has a curve in the threshold and it says to have 3/8 clearance for the step. It’s hard to tell with the brush on bottom of screen door. Has anyone put the...

I know on the brisk 2 units in order to acess some bolts to change fan motor you have to take the ac unit completely off to access the bolts from the bottom. What a bummer they did that. Was prolly done on purpose to get you to buy more parts. So if you have a brisk your gonna need a new seal...

I did something similar. I took a piece of sheet metal and bent it and cut it so it’s goes straight to it the vent the flow out vents is much better. I also took off all aluminum tape and put up sheets of metal and screwed them to the frame. Then I put gorilla tape in the corners. It’s sealed...

When I bought the rv all that aluminum tape was in the condenser.

I took the whole inside apart took off all the junk tape, put spray foam in the voids covered back up seams with gorilla tape then did the mod where you put a sheet metal piece in forcing the air out the vents. It send out the vents way better. I cleaned all the condenser. I did feel air coming...

Someone said they put out more air? I read a little about they talk about guieter but the air is was noisy to me. Can’t hear the tv when on.

Freeze sensor is in place. It’s freezing on the opposite side. I don’t understand why.

I have a 75 gallon trax3 transfer tank to sell. It’s 2 yo. Works fine everything included. 800$

We have 57% humidity so far today. Gonna get worse. I have the fans on high now. I will see how it works. I’ve left the cover off so I can look up see easier tonight when I get home - - - Updated - - - We have 57% humidity so far today. Gonna get worse. I have the fans on high now. I will see...

So I left for the entire day yesterday got home realized I left the ac on auto. It had shut off and seemed fine, 30 minutes later it kicked on I could feel water shoot out. I knew it must’ve froze. Thought well it’s thawed out now went to bed about 1100 pm. At 2 am. I heard it kick on and a boom...

When I bought trailer there was no filter on the unit and it was dirtiest I had ever seen. I cleaned it very good, put a filter on it. I may check it again. I will try running on hi. It runs all day anyway when the sun comes up.

I currently have 3 ac units on my cyclone 4000. I am running 2 at a time. But they both seem to freeze up and switch to fan a lot. It is humid here. 60-80 % most of the time. But the bedroom ac is getting hung up sometimes. When it switches from cool to can it will sit there and humm and hiss...

I seen on the new toy haulers they have new legs on the back to help the cables and they double the weight rating. Anyone know what the part number and manuafacture is?