Search results

Bought new, used very little. Many accessories and equipment will go with it. Kept clean and waxed. Dealer detailed prior to last use. No issues, no problems - other than can't find the time to use it. Located in TN. Will forward specs, sale sheet, pics, list of accessories, etc. as next step...

Plate setter is a must for the best indirect cooking around, use mine more often than not. Unfortunatly a pizza stone will not work due to not holding up to the heat. It will crack. For the best steaks, go direct with the bottom and top dampers open 100%. When the temp reaches north of 800...

Congrats Ziggy. Lovin our large one as well. Had hot wings and chicken breast today, all amazing. If you havent already found it, go to the BGE website and check out the forum; thousands of methods, recipes, pics, etc. I use two remotes to stay on top of internal meat temp and dome temp.

Thank you for the good info.

Opened the slide out on top of a low utility trailer in storage, learned the lesson about always checking for clearance first. The damage is limited to a sheet metal section just behind the white plastic fender. It appears all that is needed is to drill out some rivets and replace the small...

Dave, we'll be there 3/15 through about 3/22.

Thank you all for the great info, and a great forum. Sure is nice to get such good info and prompt.

Planning to visit our son in the Virginia Beach area in March. Any insight available on First Landing State Park, or advice for other campground options close by? Equipment is an 08 Sundance FW, 3300BHS. Thank you all for any advice you may offer.

Thats a good start Ray. After years of various smokers, gas and charcoal grills, etc., finally got it right and bought into this big green egg thing. Its a beast that holds heat from 200 to 800 degree f with a limited amount of lump charcoal. Great smoker, low and slow for hours without error...

Hello neighbors, getting cold in Ringgold tonight. About time to head to Topsail in the Destin area. Enjoy Fort Mountain here local, Chester Frost can be nice when the crowds are down. Enjoying our new Sundance 3300BHS.

Just bought a BGE. Any favorite methods and meat choices to share?

Tech service at Heartland said the fuse was between the switch and motor. After digging and pulling apart wires, found the tapped up fuse between the battery and the switch. Gee thanks service techs. Good to go again.

After weeks of homework, settled on one of two models; the Sandpiper or the Montana Mountaineer. When looking at one of these for the third time, with the intent of purchasing, noticed a Sundance parked close by that we had not looked at prior because if was much less cost, about 38% less in...

Finally got a chance to search for the fuse and was not in clear sight, nor felt anything like a fuse within the plastic shroud material containing the wires. Should I peel this stuff back, or is it possible it is located elsewhere?

Thanks again, good description. Am learning that my shade tree mechanic ideas have no place on a camper.

Looked all around the battery but didn't find a fuse. Will look again and much closer. Not familiar with how the break away system works, but will heed your advice here as well. Thank you.

Motorized legs have stopped working. Was in the process of leveling by extending the legs and stopped with no hint of a problem. No blown fuse or tripped breaker. Before going through the hassles of returning for service, any check points suggestions? Camper is FW, 08 3300BHS, Sundance. Also...

Thank you both.

Out with the TT, and in with the first FW, 08 3300BHS. First outing starts this weekend. Our use rate will be one or two continuous weeks annual maybe 600 miles one way, and 6 - 8 long weekend shorter trips, less than 150 miles. New to forum, and thanks for the great info that has already been...

Thanks all. No where in the manual does it show/explain placement for the slide out manual crank. Hopefully will not be needed on the maiden trip next week, but now armed and ready.

With our 08 3300BHS is a tool similar to a deep well socket but sloted on the end. What's its purpose? Thanks