Recent content by psdl*99

Can the OP and others comment on their 371 experience? I am looking at one. We currently have a 2009 Razor 3216TS. It's been a great unit for us. Well made and held up well. A few questions about the 371... 1. What issues have you encountered so far? 2. What are your complaints? 3. How is...

My storage location just told me that the running gear of my 2009 Razor 3612 has a broken shackle and a few others are getting close to breaking. In looking for a replacement shackle kit I came across the MOR-ryde LRE12-004, a wet bolt upgrade kit. How do I know if this suspension Heartland...

The past 4 days have been interesting and result in a body repair shop for internal and external issues. 1. Aug 18 - A golf cart ran into the door side at full speed. No one was aboard or hurt thank goodness. Damage to skirting under kitchen slide out, main steps, and skirting toward front of...

Our JVC DVD player is not working. I want to put a regular DVD player in but can not get access to the back of the TV to plug the cables in. Can someone guide me on how to access the back of the TV? I suppose if I pull hard enough I will get there... but probably not advised.

Smoke, The valve in question changes where the water pump is pulling from (fresh water tank or RV antifreeze syphon tube). There is a separate inlet for black tank flush. I have a 3612 and winterized it 2 weeks ago. Here is what I did. 1. Pull kitchen drawer out above water heater. Reach in...

Update: After the first three trips this year I went through three fuses. The dealership tested the motor draw and it was actually pulling 40 amps. The motor manufacturer sent out a new motor and it was swapped in June. No problems since.

While washing the bugs off the front cap of our 3612 I noticed two areas (center just below decal) where the figerglass is starting to spider web. There are no indications of hitting anything (chips, dents) in the area. Should I be concerned about this? Will it lead to problems? What are my...

Kenny, Eternabond is the product that was installed. Even though this may be considered a perm fix I wonder what would happen if there is future water damage. Would I be SOL if I did not replace the roof and there was water damage? I have no problems putting in a claim... that's why I have the...

I have a 2009 3612 purchased in March 2008. We have been out 15 times so far this searson and love the unit. Last Friday I hit a low hanging branch (3 inch diameter) dragging it from front to back of the roof. Along the way it tore a long line in the roof liner, tore off a Maxair vent cover...

I took delivery of our 2009 3612 at the end of Feb and started to blow landing gear motor fuses before our first trip. I ended up replacing three of the 30amp fuses before I took it in to the dealership. There test showed it was drawing 40 amps. They ended up getting a replacement motor...

Dealer said they could get me in on April 9 but I did not want to wait any more. I pulled the switch out and there was the loose wire... mystery solved. So, my short list of repairs is a little shorter. I still love this thing. Thanks for the ideas, I may do the breaker if the fuse gives me...

3612 I took delivery of the Minneapolis show unit back on Feb 28. I pulled it home and parked it (waiting for the snow to melt). Over the last week I've finally been able to move it down to my shop and started installing wheel chocks in the garage, shelving unit, and loading it for our first...

Still no luck HT - My 3612 has the same setup you describe and picture. There is a 30 amp fuse just above the gen enclosure. The fuse was OK. I pulled it, inspected it, then pushed it back in. Still nothing. I can not reach the motor or the wires behind the switch due to the gen enclosure...

Mcgyan Process for producing biodiesel You will hear more of a newly developed process for producing biodiesel called the Mcgyan process. http://www.evercatfuels.com/technology.asp It is still biodiesel but produced in the most effective way yet (time and cost).

Thanks Smokey. I am not able to access the area behind the switch due to the generator compartment wall and the ODS propane tank compartment wall. The bottom is buttoned up also. The switch panel would have to be unscrewed and pulled out. While I am fine doing this I'd rather the dealer...