Search results

Reading all of this adds support to my buying Goodyear tires...I have had two failures on Goodyear's and Goodyear stepped up immediately. I sent pictures of the damage and the failed tire ($3,500 in one case) and within a couple of weeks I had a new tire and a check for the trailer repairs...

Thanks guys, I checked the "plug in's for all systems in the entertainment center, all OK. There was no loss of power to anything else in the trailer, microwave, RAC. I have a voltage meter in the trailer..all seemed well. I think that would eliminate the thought of loosing one leg and if I...

The other morning we woke up to find we have no power to the TV, DVD or anything else (120V) in the rear (3400RE) entertainment systems..The 12V cabinet lights all worked. This outage was only with the TV, DVD, and all things in the rear wall where our TV and all other things (120V) I...

Don't think so Dan...that one does not have a slot in the socket that I can tell. Take a look at John's post...Looks like I may have been looking for the wrong crank. Thanks for the response anyway. Larry

BINGO JOHN....that will work for me! I have been trying to find slotted socket crank that will fit over the rear scissor jacks with a pin in it. Never thought ablout a crank sans slotted socket...I'll start looking for one you describe...I'm not to optimistic though....I've goggled Cranks...

I have exhausted all efforts to find a replacement crank for the rear electric scissor jacks on my 2008 Bighorn. You would think that Heartland would make the Landing Jacks and the rear stabilizer scissor jacks take the same crank, but the female end on the rear jacks is smaller. I've tried...

Unfortunately, Samsung has had it's problems with their power boards. It seems to be a common problem. Google "my samsung turns off or my samsung won't turn off". You should see numerous post and what prople are doing about the problem..Good luck.. BTW, I never got mine fixed...when it won't...

Thanks guys for the tips... Larry

Thanks to all...good information.

Planning a trip from Memphis, TN to the North Carolina line, via I40. Any suggestions on campgrounds along the way? We won't mind traveling about twenty or thirty miles off I40. Our destination is about 550 miles up I40 and we like the 250 mile 2:00 rule for traveling. Thanks for any...

Thanks guys...found the manual and I'll follow the instructions.

Re: Gap on slide seal..big! Problem solved..On site service call. Tech. adjusted slide for proper seating done deal..cost $80.00. All is good!

We are experiencing a strong sulfur smell from our hot water. The smell dissipates if we let it run for about thirty seconds. We are not experiencing an odor from the cold water side. We have a filter incorporated in our shore water feed. At the beginning of this season I drained and...

Re: Gap on slide seal..big! OK guys...sounds like my problem isNOT a piston adj. solution..We are currently camping and I think I'll wait until I get home where I can get some help... Thanks to all for helping me with this problem. I will post later as to my outcome. Thanks again to all.

Re: Gap on slide seal..big! Now what?...I have studied the lippert instructions (thanks Jim) and it looks like I need to either "synchronize" or adjust the the "piston" per their instructions but I don't know which procedure. Since it appears to seal on all sides with a gap at the top right...

Re: Gap on slide seal..big! Thanks Jim..I'll check info. you posed.. Dan, no obstructions...

My ODS living room slide has a significant gap at the right side top. Large enough to feel wing intrusion and you can see light. I would say the gap is about an inch at it's worst point. Left side of slide seals good. I know that slides can be adjusted but is this best left to an "expert"...

Thanks guys..all good ideas. To expound on my original post. I do use a short section of hose (3' approx) to fill my tank while first blowing into the fill port to remove any water via sag. John wrote that "I could be pulling air at the pump". My take on this is that if that was happening I...

08' 3400RE 75 gallon fresh water tank. We don't use our fresh water tank very often but on our current trip we had to fill the fresh water tank. I extremely dislike the system for filling the tank. All previous 5R's have had a valve that allows you to fill fresh water tank while hooked up to...

Thanks Dan, this gives me something to work with..

OK, thanks for the response. But, I have no idea where to look for the ground wire...any help..anyone?

I don't fill my fresh water system very often, only about three or four times since having the RV....This last time I filled fresh water holding tank a strange thing happened. After filling, all monitor values topped out to "full". I, like most RV'rs, don't put any confidence in the monitors...

I have a Dometic Mdl# NDM1062 I have had to replace the door latch/handle on the average of once a year. They have all broken in the same place. It appears to me it's a flex problem with the two small flexible tabs on the handle . While I appreciate that things wear out...this is too ofter...

Thanks, I'll look for the hidden screws...

I need to make a repair to one of my day/night shades. I have a string that has untied in the header. To get to the shade I need to take the valance off. I cannot figure out how to remove the valance. I can't seem to see how it's attached. If anyone has had experience removing the valance...

I have completed the process to obtain a Tennessee gun carry permit. Wondering if anyone from Tennessee has applied for a permit and how long it took to receive your permit. I've asked the powers to be and got answers anywhere from thirty days to ninety days???? If there is anyone out there...

Thanks Dan, looks like they have added an addendum to the manual...I'll give that a try but I really don't see how this will work with(if in fact Dometic is using them) pop-rivets...but what do I say?

Thanks Dan, it's a Dometic NDR1062...I was able to find a manual...below is all it states...not much information... The lamp is located at the top of the refrigerator compartment. To replace the lamp, follow these steps: Remove the lamp cover. Wearing gloves, pull out the lamp from socket...

I have read all the post here and I have not seen anyone post that has installed a fan in a Dometic with the light on/off switch on the refer. ceiling interior with the push pin switch. I can't figure out how to get the light housing off. I did see a diagram of the switch and it looks like...

I'm not sure what you mean by "puck" light, but usually the overhead lights take regular 12v automotive bulbs...I think they are 1257's...you could take one of the bulbs out and match it up at Lowe's or Home Depot.

Welcome Dave and Shelly...you've joined the best forum on the Internet....Drive safely and have fun. BTW, we go to Taos almost every year and usually stay at Trailer Ranch...

Here ya go John, I found the post...Is this what you were looking for?

John, someone has poster pictures on the forum depicting wheels cracking ....The photos I've seen have all been on the spokes and near as I can tell, there wheels were the same as mine. The cracks the I've seen are all on the spokes in a perpendicular configuration..

After seeing a post here on cracked wheels, I checked mine very closely and I don't believe I've got any cracks. It actually looks like something caustic got on the wheels and ran down the wheel..There is no evidence of any white powder as a result of corrosion. What I planned to use is a small...

I have some very small scratches on some of my wheels (2008 3400RE). I was wondering if I could clear-coat these scratches for some positive results? None of these scratches are into the metal...all seem to be surface scratches..any suggestion? Larry

Looks like it's for an iPhone or iPad only...No app for a laptop?????

Drained my Hot water tank for winterazation and my anode rod is fairly calcified up. It still has good thickness and I was wondering if I could clean it up and reuse it. I took a wire brush and got it looking pretty good. Are these rods just coated with the magnesium and over time does the...

Thanks guys for the responses..

I'm doing some mods. to my basement area and wanted to get some ideas on shelving...not anything heavy, wanted to get a few items that get in the way when on the floor and I don't want to go to my bins each time. I've already been using plastic bins. I've looked at some wire shelving and it...

Thanks guys for the replies..I think I'll be alright..